mirror of
https://codeberg.org/scip/attinycore-makefile-tests.git
synced 2025-12-16 19:00:57 +01:00
108 lines
2.0 KiB
C++
108 lines
2.0 KiB
C++
/* -*-c++-*-
|
|
Blink
|
|
Turns on an LED on for one second, then off for one second, repeatedly.
|
|
This example code is in the public domain.
|
|
*/
|
|
|
|
/*
|
|
./hardware/ATTinyCore/avr/cores/tinymodern/core_pins.h
|
|
Caution: reverse Pinout: PA3 => Pin 3
|
|
|
|
Nanite841 Pinout from above:
|
|
|
|
button
|
|
SDO/MISO PA5 PA6 SDI/MOSI
|
|
SCK PA4 PA7
|
|
CS PA3 PB2
|
|
RX0 PA2 PB2
|
|
TX0 PA1 PB1
|
|
PA0 PB0
|
|
GND VCC
|
|
usb
|
|
|
|
Bosch BME280 Breakout from above pin header left:
|
|
|
|
VCC
|
|
GND
|
|
SCL => SCK
|
|
SDI => MOSI
|
|
CSB => PA3/3
|
|
SDO => MISO
|
|
|
|
*/
|
|
|
|
#include <avr/io.h>
|
|
#include <util/delay.h>
|
|
#include "841vcc.h"
|
|
#include "841sleep.h"
|
|
|
|
#define NODE_ID 1
|
|
#define OUTPUT_PIN 7
|
|
#define LED 2 //LED_BUILTIN // PORTB2
|
|
#define CS 3
|
|
#define DELAY 5000
|
|
#define WDTREPEATS 10 // results in 8s x 10 times == 80 seconds sleep
|
|
|
|
#define SET_OUTPUT(pin) DDRB |= (1 << pin)
|
|
#define SET_HIGH(pin) PORTB |= (1 << pin)
|
|
#define SET_LOW(pin) PORTB &= ~(1 << pin)
|
|
|
|
void print_asufloat(uint32_t val, uint16_t factor) {
|
|
Serial.print(val / factor);
|
|
Serial.print(".");
|
|
Serial.print(val % factor);
|
|
}
|
|
|
|
void print_asifloat(int32_t val, uint16_t factor) {
|
|
Serial.print(val / factor);
|
|
Serial.print(".");
|
|
Serial.print(val % factor);
|
|
}
|
|
|
|
void print_measurements() {
|
|
float vcc;
|
|
|
|
SET_LOW(LED);
|
|
|
|
adc_enable();
|
|
adc_start();
|
|
vcc = adc_get_vcc();
|
|
adc_disable();
|
|
|
|
Serial.print("Voltage: ");
|
|
Serial.println(vcc);
|
|
|
|
SET_HIGH(LED);
|
|
}
|
|
|
|
void halt() {
|
|
while(1);
|
|
}
|
|
|
|
|
|
void setup() {
|
|
SET_OUTPUT(LED);
|
|
Serial.begin(115200);
|
|
Serial.println("init");
|
|
delay(4000);
|
|
adc_setup_vcc_measurement();
|
|
sleep_setup();
|
|
}
|
|
|
|
void loop() {
|
|
uint8_t i;
|
|
print_measurements();
|
|
Serial.println("delay...");
|
|
delay(10000);
|
|
for(i=0; i<WDTREPEATS; i++) {
|
|
Serial.print("----- ENTER SLEEP: ");
|
|
Serial.println(i);
|
|
sleep_enter();
|
|
Serial.println("----- LEAVE SLEEP");
|
|
}
|
|
Serial.println("-- DONE");
|
|
}
|
|
|
|
sleep_vect();
|
|
|