rpnc/archived/README.md

## Reverse Polish Notation Calculator for the commandline

This is a small commandline calculator which takes its input in
[reverse polish notation](https://en.wikipedia.org/wiki/Reverse_Polish_notation)
form.

It  has  an  unlimited  stack,  supports  various  stack  manipulation
commands, can be used interactively or  via a pipe and has a collector
mode. It doesn't have any other dependencies than Perl.

## Usage

Calculate the summary  resistance of parallel resistors  with 220, 330
and 440 Ohm using the following formula:

    1 / (1/R1 + 1/R2 + 1/R3)

Here's the sample session:

     0 % 1
    stack    1: 1
    
     1 % 1
    stack    2: 1
    stack    1: 1
    
     2 % 220
    stack    3: 1
    stack    2: 1
    stack    1: 220
    
     3 % /
    stack    2: 1
    stack    1: 0.00454545454545455
    
    => 0.00454545454545455
    
     2 % 1
    stack    3: 1
    stack    2: 0.00454545454545455
    stack    1: 1
    
     3 % 330
    stack    4: 1
    stack    3: 0.00454545454545455
    stack    2: 1
    stack    1: 330
    
     4 % /
    stack    3: 1
    stack    2: 0.00454545454545455
    stack    1: 0.00303030303030303
    
    => 0.00303030303030303
    
     3 % 1
    stack    4: 1
    stack    3: 0.00454545454545455
    stack    2: 0.00303030303030303
    stack    1: 1
    
     4 % 440
    stack    5: 1
    stack    4: 0.00454545454545455
    stack    3: 0.00303030303030303
    stack    2: 1
    stack    1: 440
    
     5 % /
    stack    4: 1
    stack    3: 0.00454545454545455
    stack    2: 0.00303030303030303
    stack    1: 0.00227272727272727
    
    => 0.00227272727272727
    
     4 % +
    stack    3: 1
    stack    2: 0.00454545454545455
    stack    1: 0.0053030303030303
    
    => 0.0053030303030303
    
     3 % +
    stack    2: 1
    stack    1: 0.00984848484848485
    
    => 0.00984848484848485
    
     2 % /
    stack    1: 101.538461538462
    
    => 101.538461538462

The *%* character denotes the interactive prompt. What we basically entered was:

    1 1 220 / 1 330 / 1 440 / + + /
    
Which translates to:

    1 ((1 / 220) + (1 / 330) + (1 / 440))
    
So,  you're entering  the numbers  and operators  as you  would do  on
paper. To learn more, refer to the Wikipedia page linked above.

## Collector mode

Beside  traditional RPN  you can  also  enter a  special mode,  called
*collector mode* by entering  the <kbd>(</kbd> command.  The collector
mode  has its  own stack  (a  sub stack)  which is  independed of  the
primary stack.  Inside this  mode you can  use all  operators, however
they work on *ALL* items on the sub stack.

So, let's compare. If you had in normal RPN mode the following stack:

    3
    5
    6
    
and then entering the <kbd>+</kbd>  operator, the calculator would pop
5 and 6  from the stack, add them  and push the result 11  back to the
stack.

However, if  you are in collector  mode with this stack,  then all the
items would be added, the sub stack would be cleared and the result 14
would be added to the primary stack.

You  will  leave  the  collector  mode  after  an  operator  has  been
executed. But  you can  also just  leave the  collector mode  with the
command  <kbd>)</kbd> leaving  the sub  stack intact.   That is,  upon
re-entering collector mode at a  later time, you'll find the unaltered
sub stack of before.

## Undo

Every operation which  modifies the stack can be  reversed by entering
the <kbd>u</kbd> command. There's only one level of undo and no redo.

## Functions

You can define functions anytime directly on the cli or in a file called
`~/.rpnc`. A function has a name (which must not collide with existing
functions and commands) and a body of commands.

Example:

    f res2vcc 1.22 R1 R2 + R2 / 1 + *

Which calculates:

    (((R1 + R2) / R2) + 1) * 1.22 = ??
    
To use it later, just enter the variables into the stack followed by the
function name:

    470
    220
    res2vcc
    => 2.79

You  can  also  put  the   function  definition  in  the  config  file
`~/.rpnc`. Empty lines and lines beginning with `#` will be ignored.

Another way  to define a  function is to  use perl code  directly. The
perl code must  be a closure string and surrounded  by braces. You can
access the stack via `@_`.  Here's an example:

    f pr { return "1.0 / (" . join(' + ', map { "1.0 / $_"} @_) . ")" }
    
This  function  calculates the  parallel  resistance  of a  number  of
resistors. It adds up all values from the stack. Usage:

    22
    47
    330
    pr
    => 41.14


## Using STDIN via a PIPE

If the commandline  includes any operator, commands will  be read from
STDIN, the result will be printed  to STDOUT wihout any decoration and
the  program will  exit. Commands  can be  separated by  whitespace or
newline.

Examples:

    echo "2 2" | rpnc +
    (echo 2; echo 2) | rpnc +
    
Both commands will print 4 to STDOUT.


## Complete list of all supported commands:

### Stack Management

* <kbd>s</kbd>    show the stack
* <kbd>ss</kbd>    show the whole stack
* <kbd>sc</kbd>    clear stack
* <kbd>scx</kbd>   clear last stack element
* <kbd>sr</kbd>    reverse the stack
* <kbd>srt</kbd>    rotate the stack

## Configuration

* <kbd>td</kbd>    toggle debugging (-d)
* <kbd>ts</kbd>    toggle display of the stack (-n)

## Supported mathematical operators:

* <kbd>+</kbd>     add
* <kbd>-</kbd>     substract
* <kbd>/</kbd>     divide
* <kbd>*</kbd>     multiply
* <kbd>^</kbd>     expotentiate
* <kbd>%</kbd>     percent
* <kbd>%+</kbd>     add percent
* <kbd>%-</kbd>     substract percent
* <kbd>%d</kbd>     percentual difference
* <kbd>&</kbd>     bitwise AND
* <kbd>|</kbd>     bitwise OR
* <kbd>x</kbd>     bitwise XOR
* <kbd>m</kbd>     median
* <kbd>a</kbd>     average
* <kbd>v</kbd>     pull root (2nd if stack==1)
* <kbd>(</kbd>    enter collect mode
* <kbd>)</kbd>    leave collect mode

## Register Commands

* <kbd>r</kbd>    put element into register
* <kbd>rc</kbd>   clear register
* <kbd>rcx</kbd>  clear last register element

## Various Commands

* <kbd>u</kbd>    undo last operation
* <kbd>q</kbd>    finish (<kbd>C-d</kbd> works as well)
* <kbd>h</kbd>    show history of past operations
* <kbd>?</kbd>    print help

## Converters

* <kbd>tl</kbd> gallons to liters
* <kbd>tk</kbd> miles to kilometers
* <kbd>tm</kbd> yards to meters
* <kbd>tc</kbd> inches to centimeters
* <kbd>tkb</kbd> bytes to kilobytes
* <kbd>tmb</kbd> bytes to megabytes
* <kbd>tgb</kbd> bytes to gigabytes
* <kbd>ttb</kbd> bytes to terabytes

## Function Comands

* <kbd>f NAME CODE</kbd>  define a functions (see ab above)
* <kbd>fs</kbd>   show list of defined functions


## Copyleft

Copyleft (L) 2019 - Thomas von Dein.
Licensed under the terms of the GPL 3.0.