fixes

841-tinycore-micronucleus-bme280-spi-radio-test/SensorSerial.ino

@@ -43,7 +43,7 @@ SDO/MISO PA5          PA6 SDI/MOSI
 #define OUTPUT_PIN    7
 #define LED           2 //LED_BUILTIN  // PORTB2
 #define CS            3
-#define DELAY         5000
+#define DELAY         1000
 
 static tiny::BME280 sensor;
 RFTransmitter transmitter(OUTPUT_PIN, NODE_ID);
@@ -68,6 +68,7 @@ void print_asifloat(int32_t val, uint16_t factor) {
 void print_measurements() {
   uint32_t pres, humidity;
   int32_t  temp;
+  int vcc;
 
   temp     = sensor.readFixedTempC();
   humidity = sensor.readFixedHumidity();
@@ -87,7 +88,19 @@ void print_measurements() {
   print_asufloat(humidity, 1000);
   Serial.println(" %");
 
+  
+  ADCSRA |= _BV( ADSC );
+  while( ( (ADCSRA & (1<<ADSC)) != 0 ) );
+  //vcc = 1.1 * 1024 / ADCW;
+  vcc = 1024 / ADCW;
+  
+    //  vcc = (((InternalReferenceVoltage * 1024L) / ADC) + 5L) / 10L;
+  Serial.print("         Voltage: ");
+  Serial.println(vcc);
+  Serial.println();
+  
   transmitter.send((byte *)temp, sizeof(temp));
+
   SET_HIGH(LED);
 }
 
@@ -95,25 +108,16 @@ void halt() {
   while(1);
 }
 
-void print_voltage() {
-  int value;
-  ADCSRA |= _BV( ADSC );
-  while( ( (ADCSRA & (1<<ADSC)) != 0 ) );
-  value = (((InternalReferenceVoltage * 1024L) / ADC) + 5L) / 10L;
-  Serial.print("         Voltage: ");
-  Serial.println(value);
-  Serial.println();
-}
 
 void setup() {
   SET_OUTPUT(LED);
   Serial.begin(115200);
   Serial.println("init");
   // Enable ADC
+  ADMUXB |= (0<<REFS0);
+  ADMUXA |= (13<<MUX0);
+  ADCSRB |= (0<<ADLAR);
   ADCSRA |= (1 << ADEN);
-  ADMUXB = (0<<REFS2) | (1<<REFS1) | (0<<REFS0);
-  ADMUXA = (0<<MUX5) | (0<<MUX4) | (0<<MUX3) | (0<<MUX2) | (0<<MUX1) | (1<<MUX0);
-  ADCSRB = (0<<ADLAR);
   //analogReference( INTERNAL );
 
   if(sensor.beginSPI(CS) == false) {
@@ -124,7 +128,6 @@ void setup() {
 
 void loop() {
   print_measurements();
-  print_voltage();
   delay(DELAY);
 }
 

841-tinycore-micronucleus-vcc-test/Makefile

@@ -0,0 +1,53 @@
+# Arduino Make file. Refer to https://github.com/sudar/Arduino-Makefile
+
+# attiny841:
+#   BOARD_TAG          = attinyx41
+#   BOARD_SUB          = 841
+# attiny861:
+#   BOARD_TAG          = attinyx61
+#   BOARD_SUB          = 861
+# attiny85:
+#   BOARD_TAG          = attinyx5
+#   BOARD_SUB          = 85
+# attiny84:
+#   BOARD_TAG          = attinyx4
+#   BOARD_SUB          = 84
+
+ARDUINO_VERSION = 10810
+
+PROJECT_DIR              = $(shell pwd)
+BOARD_TAG                = attinyx41
+BOARD_SUB                = 841
+ARDUINO_DIR              = /usr/local/arduino
+ARDMK_DIR                = /usr/local/arduino/Arduino-Makefile
+MONITOR_PORT             = /dev/ttyACM0
+ISP_PORT                 = /dev/ttyACM0
+AVRDUDE                  = /usr/local/bin/avrdude
+ARDUINO_LIBS             = 
+ARDUINO_SKETCHBOOK       = .
+
+# mk stuff
+ALTERNATE_CORE           = ATTinyCore
+F_CPU                    = 8000000L
+MONITOR_BAUDRATE         = 115200
+AVRDUDE_ARD_PROGRAMMER   = stk500v2
+AVRDUDE_ARD_BAUDRATE     = 9600
+AVR_TOOLS_DIR            = /usr/local/avr
+AVRDUDE_CONF             = /usr/local/etc/avrdude.conf
+
+# Micronucleus
+MNINST                   = sudo micronucleus
+
+# compiler stuff
+CFLAGS_STD               = -std=gnu11
+CXXFLAGS_STD             = -std=gnu++11
+CXXFLAGS               + = -pedantic -Wall -Wextra
+CURRENT_DIR              = $(shell pwd)
+
+# keep this!
+include $(ARDMK_DIR)/Arduino.mk
+
+# install using micronucleus
+install: $(TARGET_HEX) verify_size
+	@echo "########### Press RESET on the Nanite! ##############"
+	$(MNINST) $(TARGET_HEX)

841-tinycore-micronucleus-vcc-test/README.md

@@ -0,0 +1,17 @@
+# Usable Pins
+
+```
+PIN_A0  (10)
+PIN_A1  ( 9)
+PIN_A2  ( 8)
+PIN_A3  ( 7)
+PIN_A4  ( 6)
+PIN_A5  ( 5)
+PIN_A6  ( 4)
+PIN_A7  ( 3)
+PIN_B0  ( 0)
+PIN_B1  ( 1)
+PIN_B2  ( 2)
+PIN_B3  (11)  /* RESET */
+LED_BUILTIN (2)
+```

841-tinycore-micronucleus-vcc-test/SensorSerial.ino

@@ -0,0 +1,107 @@
+/* -*-c++-*-
+  Blink
+  Turns on an LED on for one second, then off for one second, repeatedly.
+  This example code is in the public domain.
+ */
+
+/*
+  ./hardware/ATTinyCore/avr/cores/tinymodern/core_pins.h
+  Caution: reverse Pinout: PA3 => Pin 3
+
+  Nanite841 Pinout from above:
+
+              button
+SDO/MISO PA5          PA6 SDI/MOSI
+     SCK PA4          PA7
+     CS  PA3          PB2
+     RX0 PA2          PB2
+     TX0 PA1          PB1
+         PA0          PB0
+         GND          VCC
+               usb
+
+  Bosch BME280 Breakout from above pin header left:
+
+    VCC
+    GND
+    SCL  => SCK
+    SDI  => MOSI
+    CSB  => PA3/3
+    SDO  => MISO
+  
+ */
+
+#include <avr/io.h>
+#include <util/delay.h>
+
+#define NODE_ID       1
+#define OUTPUT_PIN    7
+#define LED           2 //LED_BUILTIN  // PORTB2
+#define CS            3
+#define DELAY         2000
+
+#define SET_OUTPUT(pin) DDRB  |=  (1 << pin)
+#define SET_HIGH(pin)   PORTB |=  (1 << pin)
+#define SET_LOW(pin)    PORTB &= ~(1 << pin)
+
+void print_asufloat(uint32_t val, uint16_t factor) {
+  Serial.print(val / factor);
+  Serial.print(".");
+  Serial.print(val % factor);
+}
+
+void print_asifloat(int32_t val, uint16_t factor) {
+  Serial.print(val / factor);
+  Serial.print(".");
+  Serial.print(val % factor);
+}
+
+void print_measurements() {
+  float vcc;
+  
+  SET_LOW(LED);
+
+  ADCSRA = (1 << ADEN);                   // enable ADC
+  _delay_ms(10);                          // give it some time to settle
+  ADCSRA |= _BV( ADSC );                  // start measuring
+  while( ( (ADCSRA & (1<<ADSC)) != 0 ) ); // till it's completed
+  // >> 1.1 * 1024 / 225 #=> 5.006222222222223
+  // >> 1.1 * 1024 / 341 #=> 3.3032258064516133
+  vcc = 1.1 * 1024 / ADCW;                // read actual measurement
+  //  ADCSRA &= ~(1<<ADEN);                   // we're done, disable ADC
+
+  Serial.print("Voltage: ");
+  Serial.println(vcc);
+  
+  SET_HIGH(LED);
+}
+
+void halt() {
+  while(1);
+}
+
+
+void setup() {
+  SET_OUTPUT(LED);
+  Serial.begin(115200);
+  Serial.println("init");
+
+  // Setup the ADC
+  // https://www.avrfreaks.net/forum/measuring-vcc-attiny841-using-adc-and-internal-bandgap#comment-2862601
+  ADMUXB = (0<<REFS0);  // enable REFS0 bit == internal 1.1 bandgap
+  ADMUXA = (13<<MUX0);  // use channel #13 to read the bandgap (binary 1101, see table 16-3)
+  ADCSRB = (0<<ADLAR);  // do not left shift result
+
+  // disable ADC for powersaving
+  //  ADCSRA &= ~(1<<ADEN);
+
+  // disable analog comperators for powersaving
+  ACSR0A |= _BV(ACD0);
+  ACSR1A |= _BV(ACD1);
+}
+
+void loop() {
+  print_measurements();
+  delay(DELAY);
+}
+

841-tinycore-micronucleus-vcc-test/hardware

@@ -0,0 +1 @@
+/usr/local/arduino/hardware

841-tinycore-micronucleus-vcc-test/libraries/RFTransmitter

@@ -0,0 +1 @@
+/usr/local/arduino/hardware/ATTinyCore/avr/libraries/RFTransmitter

841-tinycore-micronucleus-vcc-test/libraries/SPI

@@ -0,0 +1 @@
+/usr/local/arduino/hardware/ATTinyCore/avr/libraries/SPI

841-tinycore-micronucleus-vcc-test/libraries/TinyBME280

@@ -0,0 +1 @@
+/usr/local/arduino/hardware/ATTinyCore/avr/libraries/TinyBME280